Code Details
| Display code | WABCO MM-0112 SPN 790 FMI 7 |
|---|---|
| SPN | 790 |
| FMI | 7 |
| OEM code | WABCO / ZF SID 2 |
| Manufacturer | WABCO / ZF |
| System | ABS / ESC |
| Component | Right Front WSS |
| Source address | Unknown or not applicable |
| Severity | high |
| Review status | ai source checked |
| Source confidence | high |
| Last reviewed | 2026-03-31 |
Plain-English Meaning
This WABCO ABS code flags a signal concern at the right-side front axle wheel end that WABCO attributes to the tone ring or wheel-end itself — FMI 7 means the signal pattern is not what a properly installed, undamaged sensor and tone ring would produce. Unlike FMI 3/4/5 which indicate electrical circuit faults, FMI 7 typically points to a mechanical wheel-end concern: a damaged tone ring, missing or uneven teeth, debris between sensor and ring, or an excessive air gap.
The WABCO MM-0112 table maps SPN 790 FMI 7 and SID 2 to Right Front WSS / tone ring or wheel-end signal concern. This page paraphrases the factual mapping and does not reproduce WABCO troubleshooting procedures.
Common Symptoms
- ABS warning lamp active
- Signal irregularity at the right-side front axle wheel rather than a simple open/short pattern
- WABCO diagnostic software may show a non-standard signal waveform at this wheel channel
- May appear intermittently at specific wheel speeds or wheel speeds near a damaged tooth
Possible Causes
Possible causes may include the items below. The list is not a parts diagnosis.
- Damaged or missing tone ring teeth — impact damage from road debris, contact with brake hardware, or corrosion-induced tooth loss
- Tone ring installed with incorrect orientation (facing inward/outward incorrectly) or wrong part number for the axle
- Excessive air gap between the sensor tip and tone ring — beyond the specification range for this sensor and ring pairing
- Metal debris (brake dust, swarf from recent machining) packed between the sensor face and tone ring
- Cracked or fractured tone ring producing inconsistent tooth spacing
First Checks
- Record the SPN/FMI, SID, active status, and all related codes. Note whether this appeared after recent wheel-end work.
- With the wheel raised, slowly rotate the wheel by hand and visually inspect the tone ring for missing teeth, cracks, bending, or debris packed into the ring slots.
- Check sensor-to-ring air gap using a feeler gauge or per WABCO specification — excessive gap from a worn bearing or improper installation will cause a low-amplitude signal similar to FMI 7.
- Confirm the tone ring part number matches the axle specification; wrong-ring installations are more common than expected after an axle replacement.
- Clean any accumulated debris from the ring and sensor face before reinstalling the sensor.
Can I Keep Driving?
ABS and brake-system codes are safety-related. Stop safely when the red stop lamp is on, braking feels abnormal, or stability control warnings are active. Do not bypass or disable brake or stability systems.
Related Lookup Pages
Sources
- WABCO ABS and E Version Hydraulic ABS Maintenance Manual MM-0112 WABCO / ZF Commercial Vehicle Solutions · oem · accessed 2026-05-05 · confidence high
Source: WABCO / ZF Commercial Vehicle Solutions, WABCO ABS and E Version Hydraulic ABS Maintenance Manual MM-0112. This page paraphrases factual fields only and is not a substitute for the original document.
Open source - TOOLBOX PLUS Diagnostic Software ZF Commercial Vehicle Solutions · oem · accessed 2026-05-05 · confidence medium
Source: ZF Commercial Vehicle Solutions, TOOLBOX PLUS Diagnostic Software. This page paraphrases factual fields only and is not a substitute for the original document.
Open source
FAQ
Does WABCO MM-0112 SPN 790 FMI 7 mean the wheel speed sensor itself is bad?
FMI 7 points to the tone ring or wheel-end signal pattern rather than a sensor electrical fault. The sensor may be functioning correctly — it is reporting an abnormal signal because the tone ring is damaged, gapped improperly, or sending a non-standard pattern. Replace the tone ring or correct the installation before condemning the sensor.
How serious is a damaged tone ring?
A tone ring with missing or damaged teeth gives the ABS ECU inaccurate speed data at that wheel, which can cause the ECU to modulate brake pressure incorrectly or leave ABS unavailable for that channel. It should be repaired before operating in conditions where ABS would be needed.
Can debris between the sensor and tone ring clear itself?
Heavy debris accumulation does not typically clear itself under normal road conditions. If the code appeared after a brake job or wheel-end service that introduced metal particles, cleaning the sensor face and ring slot area at the wheel end is the appropriate first step before ordering parts.